Hello. In this week's episode we are gonna talk about how we built this wall.
Yeah. Actually, as you guys know, this wall was... as we cut the container in half, this was what was completely empty.
So, we had to do the whole thing from scratch.
So, let's get to it.
So. This is the floor of the container, this is the wall, this is the next floor, that we gonna put,
that's 3 centimeters and then it's gonna be like a stage, like a little high second floor.
That the table is gonna be on the top of this. So, this it's 30 centimeters.
And here it's gonna be a table like this and a seat like this.
I understood.
And the window is gonna be here. So, this I'm not sure exactly how high it is.
Let's suppose.
23.
So, the window... from here...
Guten? (German)
Let's see if fits.
What are you doing, babe?
When we cut ... when we cut this structure, this.. how you say... column
did like, like this.
So, now you're pushing back on place. Pushing back to the place.
Because right now the distance on the bottom is not the same as the distance on the middle.
So, now now we're trying to pull apart , so if...
Let's see.
Now, the finally test, final test.
Is that good?
Perfect.
Good enough.
Now. Next one.
What are you doing?
Just compressing both containers together, so we can take this off.
Why do you want to take this off?
Because we put on the wrong side. Need to be sideways, not up, it's like upside down.
How about the result?
I mean, it's not perfect, but...
we are getting there.
So, we need to solve this problem now.
Yeah. Because this is thicker than this.
I'm not sure if it's possible to see.
This is thicker than this.
So, we have a hole here and we need to cover. So, we are gonna get a small...
we're gonna just get a small part of this steel,
we're gonna cut a stripe here, and we're gonna weld on the end here.
So, Maycon is the one that cuts and I'm the one that weld.
Ok.
Team work.
And she is the one that films.
What happened?
No, I'm just... Just take me off the gas so we can bring the machine inside.
Why?
Because it's too windy.
So, is that working?
So so.
Because now we're working with the container plate it's a little bit different.
And the wind is really... not really strong but for welding is strong.
So, if the wind blows the gas off it's pretty hard to weld, but we'll try.
So. Here inside the better than outside?
Yeah. We came inside, I'm just tick welding every little, I don't kown, 10 to 20 centimeters,
and then... just to hold on place,
and then tomorrow, hopefully, if there's no wind, I'll weld outside, the whole line.
But, the forecast says that will be raining.
The whole week.
So, what is the plan for today?
Well, we need to clean up the welds, on the bottom, and then we need to finish the weld on the top,
and on the sides.
If.. after that, we still need to put a cold zinc to protect the weld.
If we have time, we'll give a primer paint after dries.
And if we have time, even more, if it doesn't rain, we need to measure and cut the top part.
Another one, just like this.
There.
Yeah. The worst part is to put the piece there.
Yeah. But let's get to work.
Yep.
That's what happen when you forget to turn on the gas.
And that's why the other day was really hard to weld.
Because there was a lot of wind and I didn't know what was going on.
But, it was the wind that was taking the gas off, so you could not get a perfect weld.
And today you forgot to turn on the gas.
Yeah. Let's do it. Let's try it now.
For real now.
That's a weld getting good. That's way better.
So, we are basically just marking the spots that I need to do a little fixing
on the welding, because there is a small hole and we want to make sure it's watertight.
So, we're just marking the right spots.
Not bad, ah?
Not at all.
For the first time...
I guess you're getting used to the tools.
I was looking for you there. I was lost because I was looking for you.
I guess you are getting used to the tools.
Yeah.
It was really fast, actually.
Do you think so?
Yeah.
Yeah. So, now it's done.
Is actually.. it's actually not that heavy
It's lighter than I though.
Good.
So, I guess, if doesn't rain tomorrow, we might be able to do it.
It's here.
Let me show.
Can you point? Where is it?
Yeah. So, it's for this part here.
Yes. The first thing was just trying on place to see if fits,
because we are not we've never tried before.
and we just need to take, like maybe two fingers off the side...
Well, I hope you guys have enjoyed this episode.
Next week we're gonna talk about how we're gonna build the entrance door, that's gonna be right here.
See. Do you like it?
See you guys next week.
Không có nhận xét nào:
Đăng nhận xét