Today I will talk about the problems of Hummingbird machines that cost between 150 and 190 dollars in the Chilean market.
Versus the imitation dragonfly that you can buy it in 30 or 45 dollars that for the value the people can look at it with distrust in comparison with the Hummingbird.
I will prove otherwise, the Hummingbird machine does not even meet the minimum design
First we will show the operation of the machine Dragonfly imitation with a standard grips, inserted the needle, has the system that replaces elastic band.
The output can be adjusted by adjusting the grips and this machine
works with the clip cord cable
I connect the power supply and the cord clip to the machine.
Grips and standard needle, it is operated at 3.5 volt, I can regulate its output and raise its voltage, it is a very silent machine
Meets the goal, economical, weighs 80 grams, watch how it works. All good!
As you can see the standard grips works perfect on this machine
I will show the operation of the imitation Dragonfly machine with a catridge grips
I install catridge grips, I choose the rod according to the machine, it is not necessary to use elastic nor the system that replaces it
I adjust the grips so the catridge is functional and the machine does its job
adjust the grips again so that the catridge works well
Or depending on the machine I can use another measure of rod
You can see that the machine works perfect! And the needle has no vibrations
I showed them an imitation Dragonfly machine that is very economical.
v/s The Hummingbird machine, which is becoming known in Chile this year 2017
I will show the operation of the Hummingbird machine, which uses an RCA cable.
The manufacturer of this machine recommends not using more than 7 volts. To set, set the voltage to 5 volts
First problem: According to the information attached to the machine, it says that it accepts grips, needles, standard tubes
The Hummingbird machine should be the good version of the machine I just showed you
Now let's prove the opposite
First problem: the space between the needle holder and where the grips are tightened is very short, ie it does not accept standard grips
Now I'll prove it. Look, I'm going to install the standard grips just like on any machine
I use a standard needle, observe how the needle stays, the distance and the exit
The grip must be pushed to the limit because the machine is shorter than normal
The tube length of all existing disposable grips have the same length
t becomes very difficult to put the needle because I am at the limit and the welding of the needle is touching the tip of the grips
In spite of everything, I managed to install the needle and now I will do a test
Install the RCA cable. You can see the distance in millimeters that the needle leaves, how do I regulate this?
It is not with the rear regulation that regulates the travel of the machine I must regulate with the grips, reaching the limit, not having more space to adjust
This is the Hummingbird brand that has pen, rotary machines and other products.
They advertise as a brand of very good quality
Look I'm at the limit where you can tighten the standard grips, look that the needle leaves about 5 mm
Look closely at this, I have no further distance to better adjust the needle outlet
This machine has very poor manufacturing and an incredible design error
I'm not saying that its components like motor and regulation do not work.
As you could see this machine does not work with the standard grips, it does not work
This machine is no good. I have the problem of having bought 4 machines that I can not sell in my store
I can not sell something that does not serve my clients
Before displaying a product and selling it in my store, I test the products to avoid problems with my customers
This machine has a value of 100 to 140 dollars (bought from the manufacturer).
It's an absurd value for a machine that does not work and has no fix
We would need grips and needles of special measures, the machine is very high and unstable. You understand?
Another recommendation of the manufacturer is its use in a voltage of 5 volts and that is never more than 7 volts.
The big problem when using a catridge grips is that this machine lacks more than 1 cm to be normal and a design that allows work
The short catridge grip rod will be used. I put the rod, I assemble the catridge grips.
I'm on the inside edge. Install the rod and then the catridge
The machine works according to manufacturer with low voltage
I am with a voltage of 4 volt, I press the pedal and the machine does not have the force to start
There is no choice but to raise the voltage, if I rise to 6 volt just the machine can start
What if I want to tattoo something at a slower speed?
According to manufacturer I should not spend the 7 volt, I understand that if I pass this voltage could have problems with the engine of the machine
When I go up to 7 volts I do not see great speed, but a normal speed
If it goes down to 5 volts, it costs to break, sometimes part sometimes not
It goes down to 4.5 volts and it just does not go away
If I really want it to work I should go up to 8 volt, voltage that does not recommend the manufacturer
A machine that says to be versatile, of a price of 190 dollars (in Chile), does not fulfill any function
Not suitable for standard disposable grips. If you work with catridge grips the machine does not have the strength to start at 5 volts
Which asks the engine for more strength. It must be used on 7 volts so that it can leave, which is not recommended by the manufacturer
Conclusion. Two machines from the same China origin, the Hummingbird machine versus the imitation Dragonfly machine
Hummingbird known in Chile in 2017 and costs $ 190. The Dragonfly imitation machine is cheaper, costs $ 40 (store price)
uses cord clip cord, connecting rod system and looks poor, but it is much better than hummingbird
The Hummingbird machine does not work! It goes straight to the trash. The Dragonfly imitation machine is very good! It's very good
The Hummingbird brand is becoming well known in Chile. Even the cheapest imitation (imitation Dragonfly) is much better
When comparing the 2 machines you can verify the differences in the distance where the needle holder is and the tightening of the grips will realize that the Dragonfly imitation machine is longer
With this last machine you can use standard grips, catridge grips, old school metal grips. A tip from a person who has spent more time selling machines than only in 2017
For more infomation >> KOREANS REACT TO LATIN FIGHTS IN DRAMAS - Duration: 9:19. 
For more infomation >> 網易雲音樂2017年九月最熱新歌TOP50 - Duration: 12:22. 
For more infomation >> Baby Dolls Learn Colours MMS Toys Surprise Tayo The Little Bus Playset Finger Family Song - Duration: 5:35. 
For more infomation >> Niepodległość Katalonii w 4 minuty. - Duration: 3:57. 
For more infomation >> Brendyn Goal - 29 minute mark - Duration: 36:19. 
For more infomation >> Mitsubishi Space Star 1.6 DIAMOND Nieuwe apk bij aflevering. Airco, hoge zit. - Duration: 1:00. 
For more infomation >> Jaguar S-Type 3.0 V6 - Duration: 1:01. 
For more infomation >> Entertainment News 247 - ＮＭＢ渋谷凪咲「みんなで大喜び」かまいたちＶ祝福 - Duration: 2:30. 
For more infomation >> v_1 - Duration: 13:23. 
For more infomation >> '미우새' 안정환 "이혜원과 데이트하다 훈련 불참, 벌금 천만원 징계" || SML TV - Duration: 2:23. 
For more infomation >> How I Make Money Online
Không có nhận xét nào:
Đăng nhận xét